Com- ponents should be at room temperature.
2 - 19 spec conversion table/ general tightening torque specifications EAS00028 service conversion table manual All specification data in this manual are listed in SI and metric units.
7 A job instruction chart accompanies the exploded diagram, providing the order of jobs, names of parts, notes in jobs, etc.2 - 33 speclubrication diagrams 1 Oil delivery hose 2 2 Oil delivery pipe 2 3 Oil filter service 4 Oil pump rotor 1 5 Oil pump rotor 2 6 Main axle 7 Oil delivery pipe 3 È To oil tank.Check: lead coupler connector Moisture Dry with an air manual blower.1 Air cut-off valve 2 Air induction system solenoid 3 Engine trouble warn- ing light 4 Fuel tank 5 Fuel pump 6 Fuel hose 7 Fuel injector 8 Throttle position sen- sor 9 Intake air temperature sensor 0 Air filter case A Fuel injection service system.In a conventional manual carburetor system, the air-fuel ratio of the mixture that is supplied to the combustion chamber is created by the volume of the intake air and the fuel that is metered by the jet manual used in the respective chamber.2 - 31 speclubrication diagrams EAS00034 lubrication diagrams 1 Oil delivery hose 2 2 Oil strainer 3 Oil delivery hose.First, tighten the lower ring nut approximately 43 Nm (4.3 m kg, 31 ft lb) by using the torque wrench, then loosen the ring nut completely.A caution indicates special precautions that must be taken to avoid service dam- age to the motorcycle.Unless otherwise specified, tightening torque specifications require clean, dry threads.Recommended Learning Management Systems (LMS) Quick Start Online Course - LinkedIn Learning Communication in the 21st Century Classroom Online Course - LinkedIn Learning Valtra Valmet 6850 tractor Service Repair Manual yjhsenjdhfjnd Massey Ferguson MF 5470 Tractor Service Repair Manual yjhsenjdhfjnd MAN Marine Diesel Engine V12-1550.1 - 5 GEN infoimportant information EAS00023 lock washers/plates AND cotter pins After removal, replace all lock washers/plates 1 and cotter pins.Keep all parts away from any source of fire.1 Fuel pump 2 Pressure regulator 3 Fuel injector 4 Throttle body 5 Intake air temperature sensor 6 Throttle position sen- sor 7 Intake air pressure sensor 8 ECU 9 Coolant temperature sensor 0 Crankshaft position sensor È Fuel system É Air system Ê Control.Disconnect: lead coupler connector.Stáhnout, xTZ_660_3YF_Service_ manual_EN, staženo:441x 1992 xtz660 katalog.6 MB (zip). When overhauling the engine, replace all gaskets, seals and O-rings.
Magneto cover) Yamaha bond.1215 Oil glossar seal holder tightening frontpage bolt Yamaha bond.1215 Oil delivery hose 2 tightening bolt Yamaha bond.1215 Lubrication Point Symbol.
Your safety IS involved!
This includes gears, cylin- ders, pistons and other parts that have been mated through normal wear.
When placing an order, refer to the list provided below to avoid any mistakes.
Create a clipboard You just clipped your first slide!Any reproduction or unauthorized use without optimal the written permission of MBK Industrie is expressly prohibited.EAS00010 table OF contents general information GEN info 1 specifications spec 2 periodic checks AND adjustments CHK ADJ 3 kriyanandapdf chassis chas 4 engine ENG 5 cooling system cool 6 fuel avchd injection system FI 7 electrical system elec 8 troubleshooting trbl shtg.2 - 32 speclubrication diagrams optimal 1 Oil delivery pipe 2 2 Oil delivery pipe 1 3 Oil filter 4 Oil pump A-.1 - 10 GEN infospecial tools Valve guide remover (ø 6) This tool is needed to remove and install glossar the valve frontpage guides.
The pressure regulator maintains the fuel pressure that is applied to the injector at 324 kPa (3.24 kg/cm2,.1 psi) higher than the intake manifold pressure.
EAS00022 gaskets, OIL seals AND O-rings.
Use this table to convert metric unit data to imperial unit data.